Ghost Controls Access Control Installation Nationwide

Ghost Controls Access Control Installation: The Carrollton Owner’s Guide

If your Ghost Controls gate system needs a new access control unit installed, replacement in Carrollton typically runs $240 to $480 for parts and labor combined, and we usually have the common Ghost Controls receiver boards and keypads on the truck same-day. The way most Carrollton homeowners discover this part has failed is simple: the remote stops working, the keypad goes dark, or the gate opens on its own at odd hours. One visit usually settles it. We identify the exact Ghost Controls control board or receiver model, match the part, and install it with a written price in your hand before anything gets touched.

Call (817) 778-4585

Which Ghost Controls Models This Applies To

Ghost Controls builds their automation kits around a few recurring control architectures, which is actually good news when a part fails. The AXDP, AXP1, and TSS1 series all share similar receiver and control-board mounting patterns, but the compatibility gotcha is the receiver frequency: older Ghost Controls systems run on 318 MHz, while the newer production shifted to 433 MHz. A 318 MHz receiver will not talk to a 433 MHz remote, no matter how many times you press the button. We check the label on the existing board before ordering anything, so you are not paying for a part that cannot pair.

If the label is sun-faded or missing (common after six or seven Texas summers), we measure the receiver’s crystal frequency directly. It takes about ninety seconds. For Carrollton properties with gates near the Arbor Hills corridor, dust is a slower killer than lightning, but when a storm does take out a board, it is usually the relay that welds shut and leaves the gate cycling continuously. OEM Ghost Controls boards are well made, but for some older models that have been discontinued, a quality aftermarket receiver matched to the correct frequency does the same job for less money. We will tell you which direction makes sense and put the part number in writing either way.

Signs Your Ghost Controls Access Control Installation Is Failing

• Remote works only from inside the property but not from the street. The receiver’s antenna wire has come loose from its terminal or has corroded inside the board housing. The antenna is a short, unshielded wire that relies on a clean connection to pick up a signal through metal gate columns.
• Keypad accepts the code but the gate does not move. This is usually a dead relay on the control board, not a keypad problem. The keypad is sending the signal correctly; the board is not passing it to the motor. Replacing the keypad first is a $90 mistake we see at least twice a month in Carrollton.
• Gate opens randomly throughout the day and night. A failing receiver can pick up stray signals from neighboring gate systems, garage door openers, or even certain older wireless weather stations. If the receiver’s metal shielding is bent or the grounding tab is broken off, it becomes an antenna for everything in the neighborhood.
• New remote will not learn, even after following the manual twice. In our experience, this usually means the receiver’s learn button is worn out or the board has entered a locked mode. It is frustrating because the manual makes it sound like a ten-second fix, but the board has stopped listening. The issue is hardware, not procedure.
• System beeps or clicks but nothing engages. When the control board relays chatter but the motor does not start, you are often hearing a failing relay. The relay is a mechanical wear part: every keypad code, every remote press, every sensor trip moves it one step closer to the end.

Before

After

Replacement Cost & What’s Included

Installed access control replacement in Carrollton runs $240 to $480, and the range is driven by which module failed and whether the gate’s existing wire runs are still usable. A straightforward receiver swap on a late-model Ghost Controls system with clean, healthy wiring is at the low end. A new keypad with a replacement receiver and some rewiring will sit at the high end. Either way, you get the price in writing before we start, under Haven Standard Clause 1, and it does not change when the job is done.

If you are seeing board damage from a lightning strike, the price range may shift upward once we see the extent of it, but you will approve the number before we proceed. Every installation includes the part number on the invoice, photographs of the finished wiring, and a function test with your existing remotes and keypad. The work is covered by our 365-Day Done Right Promise: if it is not right, we make it right for no charge within one year.

DIY or Call Us?

Let’s be clear about the safety line here: this is low-voltage work, not high-tension spring or main-power work, so the risk of serious injury is low. But the risk of buying the wrong frequency receiver and dead-ending yourself for a week is real, and wiring a new receiver into an existing gate motor incorrectly can send 24V where it does not belong and fry the motor board. That turns a $300 repair into a $900 replacement.

What you can do safely: check that the keypad and receiver are getting power, look for a tripped GFCI on the gate circuit, and note whether the keypad backlight comes on at all. That information helps us diagnose faster. But if the board is dead or the relay is chattering, call us at (817) 778-4585. We will name the part, name the price, and name what we left behind. That is the job.

FAQs