Ghost Controls Hinge & Roller Replacement Nationwide

Ghost Controls Hinge & Roller Replacement: The Carrollton Owner’s Guide

We stock and install Ghost Controls-compatible hinge and roller replacement parts in Carrollton, with most single-gate hinge or roller swaps running between $185 and $420 installed. Same-day service is available in most cases, and our trucks carry the common Ghost Controls hinge pins, rollers, and bracket hardware so we’re not ordering parts and making you wait a week. When a hinge or roller goes, you usually hear it first: a grinding drag when the gate swings, or a metallic pop followed by the gate sitting visibly lower on the latch side. The gate still runs, but the motor is now fighting dead weight, and that extra load shortens the operator’s life fast.

Call (817) 778-4585

Which Ghost Controls Models This Applies To

Ghost Controls uses a consistent hinge and roller design across its main residential swing-gate lineup, including the AXDP, AXP, and TSS1 series, along with the Ghost Controls single and dual gate kits sold through retail channels in the last six to eight years. The hinge barrels on these are typically 1-1/2 inch diameter steel with a greasable pin, and the mid-rail roller is a 2-inch sealed bearing unit mounted to a steel bracket. Before we quote a hinge or roller replacement, we confirm the measurement, because some hardware-store hinges look close but have a 1-3/8 inch barrel that binds under the weight of a full gate leaf.

We are an independent service provider, not affiliated with Ghost Controls. That said, we install OEM Ghost Controls hinges and rollers as well as a quality aftermarket equivalent when the OEM lead time is longer than the gate can wait. For most Carrollton homes, either option works, and the deciding factor is usually whether we can match the existing bolt pattern without re-drilling the gate frame. We write the part number and the brand on your job record either way.

Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

• Grinding or scraping when the gate swings. The roller bearing has run dry or cracked, and the wheel is dragging on the concrete rather than rolling. The sound typically comes from the bottom or mid-rail, not the motor.
• Gate sits low on the latch side. The hinge pins have worn into an oval inside the barrel, which drops the gate leaf a half inch or more. The gate still closes, but it scrapes or catches at the latch plate.
• Gate shudders or jerks through the travel arc. The roller is flat-spotted or seized, so the gate moves in small skips instead of a smooth swing. The motor draws more current when this happens, and that trips the Ghost Controls overload circuit on some models.
• Rust weeping from the hinge pin or roller axle. Carrollton’s freeze-thaw cycles and summer humidity put outdoor hardware through more than the manufacturer’s average lifespan estimate. Once rust is visible at the pin, the wear accelerates fast.
• The gate moved after a storm or a hard push. A hinge that was already loose will shift the gate leaf out of square, and then the operator arm has to work at an angle it was never designed for. We see this a lot after heavy wind events in Carrollton, especially on tall solid-panel gates.

Before

After

Replacement Cost & What’s Included

In Carrollton, a Ghost Controls hinge replacement runs $185 to $285 installed per hinge, which includes the new hinge barrel and pin, hardware, and the labor to lift and realign the gate leaf. Roller replacement runs $165 to $240 installed depending on whether the bracket is reusable or needs to be cut off and rewelded. If both hinges and the roller are gone, expect $340 to $420 for the full hardware refresh on a standard single gate.

The price is written and handed to you before we touch the gate. Under our Haven Standard, every job gets the price in writing up front, and the final invoice matches the quote. You also get a photo record when we leave: the old hinge, the new one installed, and the gate sitting square again. The labor is covered by our 365-Day Done Right Promise, and the parts carry the manufacturer’s warranty plus our workmanship coverage for a full year.

DIY or Call Us?

If you want to identify the problem yourself, you can safely check the visible stuff: look for rust at the hinge pins, push the gate gently by hand to feel for drag, and check if the roller actually rolls instead of sliding. That tells you whether a hinge or roller is the culprit, and it helps us quote accurately over the phone.

What you should not do is unbolt a loaded hinge from a sagging gate. The gate leaf weighs two to four hundred pounds, and once the last hinge bolt comes out, that weight has to go somewhere, usually all at once. We’ve repaired the aftermath of solo hinge replacements in Carrollton where the owner ended up with a bent gate frame and a bruised tailgate. The swap itself is straightforward for us with the right lifting setup and usually takes under an hour. If the gate is already sagging, call (817) 778-4585 and we’ll get the hardware matched before we arrive.

FAQs