Linear Gate Motor & Opener Nationwide

Linear Gate Motor & Opener in Carrollton: What to Know First

Linear gate motor and opener repair in Carrollton typically runs $240-$680 depending on whether the issue is the control board, the actuator arm, or the motor itself. We stock common Linear parts locally and complete most repairs the same day we diagnose the problem, often within two hours of arrival. Every Linear job we take in Carrollton gets a written price before work starts, so what you approve on paper is what you pay when the gate closes behind us. If you have a Linear opener that’s grinding, stopping mid-travel, or dead at the keypad, call (817) 778-4585 and a live person answers, no voicemail loop.

Call (817) 778-4585

This page is for Carrollton homeowners who already own a Linear system, or inherited one with a house purchase, and want someone who works on that specific equipment without steering them toward a full replacement they may not need. Adrian Vance and our crew have been running Linear calls across Carrollton for years, from the older residential swing setups near Arbor Hills Nature Preserve to newer slide-gate installations in newer subdivisions.

How Linear Products Fail - and How We Fix Them

• Linear LDO series swing arms and the limit-switch drift problem. The LDO50 and LDO33 linear actuators that show up on a lot of Carrollton swing gates use mechanical limit cams that shift over time, especially after a few North Texas summers. We’ll see the gate stop four inches short of closed, or slam harder into the open post than it should. The fix is resetting the limit position and tightening the cam set screw, then photographing the new position so the next tech doesn’t have to rediscover it. That’s a $140-$190 call on most Carrollton jobs.
• Linear MCS and MC series control boards losing the remote memory. When a Linear board drops its programmed remotes, the first instinct is to blame the remote. Most of the time we find the board’s memory chip lost power because of a loose harness connection or a failing backup battery on the board. We re-flash the receiver memory, reseat the harness, and test three open-close cycles. If the board is the actual fault, a replacement runs $180-$260 on the part side.
• Capacitor failure on Linear slide-gate motors during Carrollton’s summer heat. Linear slide operators (the SL and LSO lines) rely on start capacitors that take a beating when ambient temperatures sit in the high 90s for weeks. A dead capacitor means the motor hums but the gate doesn’t move. We keep the common microfarad ratings in the truck. The part itself is under $40, and labor puts the total call around $160-$220. We check the capacitor on every Linear slide-gate no-start call before ordering anything more expensive.
• Photo-eye misalignment after storms or lawn work. The photo-eye (the infrared beam that stops the gate if something crosses its path) gets nudged by weed trimmers, landscape edging, or shifting gate posts after heavy rain. A Linear gate that reverses for no reason usually has a photo-eye off by an inch or two. We realign it, shim the mounting bracket if the post has moved, and clean the lens. This is one of the simplest Linear calls we run, usually $120-$160 and done in under an hour.
• Worn carriage wheels on Linear SL slide gates making the motor work twice as hard. A slide gate operator doesn’t just power the gate, it drags it along the track, and when the carriage wheels seize or flatten, the motor pulls higher amperage and trips the overload. We see this most often on older Carrollton homes where the track sits at grade and takes on silt from rain runoff. We replace the wheels, lube the track, and check the amp draw before and after. That’s a $180-$280 repair depending on wheel count, and it often keeps a healthy Linear motor from burning itself out.

Our Linear Gate Motor & Opener Process

1. 1
   You call (817) 778-4585. A live person answers, even at 3 a.m. We ask what the gate is doing, not doing, or doing weirdly. We ask the model if you know it, but we don’t need it to dispatch.
2. 2
   We arrive and diagnose. Our technician checks the obvious failure points first: power at the board, limit positions, capacitor, photo-eye alignment, and mechanical drag. On a Linear system we’re looking at the specific failure modes listed above before we assume the worst.
3. 3
   We write the price down. You get a flat number for the repair before any work starts. That’s Haven Standard Clause 1, and it applies to every Linear call in Carrollton. If we find something else while we’re in there, we stop, show you, and price it in writing before continuing.
4. 4
   We make the repair. We use OEM Linear parts when they’re available and the right call for the job. On discontinued boards or actuators, we’ll source a quality aftermarket equivalent and tell you exactly what we’re installing and why, in writing.
5. 5
   We test, document, and hand you the record. We run the gate through at least five full cycles, test the entrapment reversal, and photograph everything: the part number that went in, the limit position, the board settings. You get that photo log before we leave.
6. 6
   The 365-Day Done Right Promise covers it. If that repair isn’t right within a year, we make it right. No argument, no fee.

Before

After

What Linear Gate Motor & Opener Costs in Carrollton

Linear repair calls in Carrollton fall into predictable ranges. A limit-switch reset or photo-eye realignment runs $120-$160. A capacitor replacement runs $160-$220. A control board replacement runs $240-$420 depending on the series. A full actuator or slide-motor replacement runs $520-$680 for most residential Linear equipment, including the motor, install, and documentation. What moves the price: whether the part is current production or discontinued, whether the mounting bracket is intact or needs fabrication, and the age of the wiring run. We don’t guess at pricing over the phone. We diagnose on site, write the number down, and you decide. Estimates are free, and the written price is the price.

Why Carrollton Homeowners Call Vance Gate Repair Carrollton for Linear Work

The Linear brand has changed hands over the years, which means parts availability varies and not every gate company keeps up with which series boards still communicate with which remotes. We stay on it because we run these calls weekly. Our technicians have been working Linear equipment since the company’s residential swing and slide lines were everywhere in North Texas, and we keep the common failure parts stocked so a Carrollton repair doesn’t wait on a freight shipment from a distributor in Ohio. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if the problem turns out to be an access-control integration issue with a third-party keypad, we’re not stuck pointing fingers at another vendor. And if your Linear motor is truly done, we’ll tell you straight and quote a replacement at the same visit, written down, no pressure.

Name what you found, name what it costs, name what you left behind. That’s the way Adrian Vance runs every Carrollton call, and the documentation you get with the repair means no future technician has to guess and no homeowner pays twice to rediscover the same limit-switch setting.

FAQs