Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Southlake, TX
Gate access control in Southlake usually means integrating a keypad, intercom, or card reader into an automated gate that weighs several hundred pounds and sits on clay soil that moves with every rain and drought cycle. Most of the calls we take here are not for simple latch fixes. They are for systems where the operator works but the entry devices do not, or where a control board failed after a lightning strike and now the whole estate is locked out. If your gate will not respond to a remote, keypad, or app, call (817) 778-4585 and we’ll walk through what is failing before sending a technician.
Why Southlake Homes Are Different
Southlake has one of the highest concentrations of automated residential gates in North Texas. The housing boom from the mid-1990s through the mid-2000s put Viking, Elite, and LiftMaster operators on hundreds of custom estates. Those systems are now twenty to twenty-five years old, which means circuit boards are failing, actuator seals are dry, and motor brushes are worn to the nub all at once across the city. Heavy wrought-iron gate panels on masonry columns put constant strain on older operator hardware.
The soil underneath Southlake makes it worse. Blackland Prairie clay expands when wet and shrinks when dry, heaving gate posts out of plumb over the course of a few seasons. A gate leaf that binds against its post or refuses to latch is often not a hardware problem at all but a shifting-column problem. North Texas ice storms, particularly the February 2021 event, also cracked exposed circuit boards and froze hydraulic actuators on systems that had never failed before.
Our Main Southlake Services
Southlake homeowners most often reach us for two reasons: an access control system that stopped talking to the gate, and a gate panel or post that needs mechanical repair. Here are the three Southlake service pages we route those calls through.
Gate Repair in Southlake
Mechanical gate repair in Southlake typically involves hinge replacement, post realignment, sag correction on heavy steel leaves, and operator troubleshooting. The clay soil and the weight of custom-fabricated panels combine to accelerate wear on hardware that would last decades in other cities. Our Gate Repair in Southlake page covers the full breakdown of what we fix and what it costs.
Gate Installation in Southlake
New gate installations in Southlake are usually measured for custom estate entrances where the column spacing, grade, and automation brand were chosen years ago. We quote in writing before any work starts and document the whole install. Our Gate Installation in Southlake page walks through the process and the price ranges.
Gate Motor & Opener in Southlake
The doors and motors on Southlake gates are now hitting the 20-25 year mark in a single wave. When a LiftMaster or Elite operator fails, the question is almost always whether the arm bracket and mounting plate are still sound enough to hold a new motor. The Gate Motor & Opener in Southlake page covers operator replacement, circuit board repair, and the brands we service.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Southlake
Gate access control in Southlake is the layer between the gate itself and the person trying to get through. Most systems here combine a keypad or intercom with a phone entry unit or card reader, and they were installed during the boom years when automation brands were just starting to integrate with home networks. Those integrations now fail in specific ways: a keypad that works from the outside lane but not the driver’s window, a phone entry system that rings an old landline that no longer exists, or a card reader that lost its programming after a power surge. We service the full stack, from the keypad faceplate to the control board, and we document every setting we change. Our Gate Access Control hub page explains the service in more depth.
Keypad Entry
Signs you need it
One or more codes stop working, the keypad backlight dies, or the unit stops responding in cold weather.
What it costs in Southlake
Keypad replacement or programming in Southlake runs between $145 and $290 per unit, depending on whether the wiring can be reused.
How we do it
We test voltage at the keypad, read the existing codes, clear and reprogram the unit, and photograph the new settings before we leave.
Phone Entry
Signs you need it
The gate dials a number that no longer exists, or calls will not connect to a mobile phone.
What it costs in Southlake
Programming a phone entry unit runs between $95 and $180; replacing the unit runs between $220 and $440.
How we do it
We verify the call route, update the stored number, and test the unit from the entry side while the homeowner stands with us.
Video Intercom
Signs you need it
The screen stays black, audio is one-way, or the app no longer shows who is at the gate.
What it costs in Southlake
Video intercom integration in Southlake starts at $190 for wiring and programming and runs up to $600 for new hardware.
How we do it
We bench-test the monitor, confirm camera power, replace or reprogram the unit, and leave a wiring diagram for the next technician.
What Gate Access Control Costs in Southlake
| Item | Typical range in Southlake |
|---|---|
| Keypad replacement or programming | $145 - $290 |
| Phone entry programming | $95 - $180 |
| Video intercom wiring/programming | $190 - $600 |
Can you reprogram an access control system the same day?
In most Southlake cases, yes. Keypad and phone entry programming is completed on the first visit unless the control board itself has failed, in which case we quote the replacement in writing before any work starts. Call (817) 778-4585 and we will tell you what we are likely looking at on the phone.
Do you work with HOA community gates in Southlake?
We service both private estates and shared community entrance gates. A single failed control board on a master-planned community entrance can lock out dozens of households, so those calls are treated as emergencies and dispatched same-day. The written price applies the same way it does on a single-family gate.
Gate Parts & Welding in Southlake
Gate parts and welding in Southlake are usually about restoring a heavy custom gate panel that has sagged, rusted, or pulled away from its post. The city’s ornate wrought-iron and custom steel panels on masonry columns were built to look right, not necessarily to distribute weight evenly across the hardware. When a hinge fails on a 600-pound gate leaf, it is not uncommon for the post to have shifted first, which means the repair is part welding and part realignment. Our Gate Parts & Welding hub details the full scope of work.
Hinge Replacement
Signs you need it
The gate leaf sags toward the latch side, scrapes the ground during the swing, or hangs visibly out of level at the top rail.
What it costs in Southlake
Hinge replacement on Southlake gates typically runs between $120 and $260 per hinge, including the weld and the alignment pass.
How we do it
We cut the old hinge, grind the mounting face clean, weld the new hinge, and set the leaf back to level before documenting the weld.
Custom Welding
Signs you need it
You find a crack propagating from a weld seam, a picket has separated from the frame, or a hinge tab has torn loose from the panel.
What it costs in Southlake
Custom gate welding in Southlake is priced per job after inspection; small crack repairs start around $160 and structural rebuilds run higher.
How we do it
We grind the crack to clean steel, bevel the edges, weld with the correct rod for the panel material, and photograph the finished seam.
Gate Rollers
Signs you need it
A slide gate chatters or jerks while moving, and you can see the roller wheels wobbling or sitting flat-spotted on the rail.
What it costs in Southlake
Roller replacement on slide gates in Southlake runs between $150 and $320, depending on the number of rollers and the rail condition.
How we do it
We lift the gate off the rail, swap each roller, inspect the rail for flat spots, and adjust the guide rollers before testing the full travel.
What Gate Parts & Welding Costs in Southlake
| Item | Typical range in Southlake |
|---|---|
| Hinge replacement | $120 - $260 per hinge |
| Small crack welding | from $160 |
| Roller replacement | $150 - $320 |
Can you weld a crack on a gate panel without removing the gate?
In most cases, we weld in place if the crack is accessible and the panel is stable. The gate stays on its hinges while we grind, weld, and cool the repair, then we photograph the seam and note the rod type in the job record. Call (817) 778-4585 to schedule a look.
Do you stock gate parts locally or order them?
We keep common hinges, rollers, and brackets on our trucks for same-day repairs, and we can usually source brand-specific parts from our Dallas-Fort Worth office inventory. Every part number we install is written into the job record before we leave, so you are never guessing what went on your gate.
Brands We Service in Southlake
We service DoorKing, Elite, Mighty Mule, and LiftMaster operators regularly in Southlake, along with five other automation brands, and we stock common boards and remotes for the major platforms. Most parts are available same-week from our DFW parts inventory. See our brands page for the full list.
Pricing for Gate Repair in Southlake, TX
| Service | Typical range in Southlake |
|---|---|
| Keypad replacement or programming | $145 - $290 |
| Phone entry programming | $95 - $180 |
| Video intercom wiring/programming | $190 - $600 |
| Hinge replacement | $120 - $260 per hinge |
| Small crack welding | from $160 |
| Roller replacement | $150 - $320 |
| Gate operator circuit board replacement | $340 - $680 |
| Remote control replacement/programming | $85 - $165 |
Southlake prices are pushed upward by the weight of the gate panels and the access required to move them. A 600-pound custom steel leaf on a sloped driveway takes longer to lift, block, and realign than a standard suburban gate, which is why we inspect before quoting and hand over a written price before the first tool comes out.
Neighborhoods We Serve in Southlake
We work across the whole city, from the gated estates along Continental Boulevard to the HOA communities off Southlake Boulevard and the older custom lots near Dove Road. Response time in Southlake is usually same-day for operator and access failures, with welding and post work scheduled within a few days.
- Timarron
- Carillon
- Shady Oaks
- Estes Park
- Northwood Hills
Service Area - Cities Near Southlake
Our crews dispatch to Southlake from the Dallas-Fort Worth office and cover the surrounding cities. If you are in Colleyville, TX or Grapevine, TX, we handle both cities on the same schedule. We also serve Flower Mound, TX and Bedford, TX, with written pricing and the same documentation on every job regardless of city.
Serving Southlake, TX - Our Local Coverage Area
We’re based in the Southlake area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Southlake
Same-day response is available for operator failures, access control outages, and shared community entrance gates that are locking out residents. We answer the phone 24/7 and we will tell you the same day whether we can get a technician to you, and when. Call (817) 778-4585 for a straight answer.
For most repairs on your own property, no. For community entrance gates or gates that sit on HOA common property, the HOA board or management company usually needs to approve the quote before we start. We provide a written price and a photo documentation packet that most Southlake HOAs accept without revisions.
On custom estate gates, we fabricate and finish replacement components to match the existing panel profile, and we can source period-consistent hardware for the 1990s and 2000s builders that dominate Southlake. We photograph the match before finalizing, so you can see the part against the original before we leave. Estimates are free, and the written price is always delivered before any work begins.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Southlake Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B.